Home - Knowledge - Details

How to Use a Paper Pot Maker: Paper Choice, Pot Size and Transplanting

Wooden paper pot maker with a finished newspaper seedling pot

A paper pot maker turns a strip of paper into a small seed-starting container by wrapping the paper around a mould, folding the lower edge and pressing that folded base into a shaping block. The finished pot can then be placed in a waterproof tray, filled with seed-starting mix and used for a short propagation cycle.

 

The basic action takes only a few steps, but reliable results depend on more than pressing the tool. The paper must be flexible and uncoated, the wrap must be snug rather than tight, the bottom must overlap completely, and the finished pots need support once they become wet.

 

Quick answer: Cut a strip of plain, non-glossy paper; wrap it around the mould with an overhang below the base; fold the overhang inward; press and gently twist the mould in the shaping block; then lift the pot off and stand it in a waterproof tray. Test the first pot before cutting a full batch because tool dimensions and paper thickness vary.

What Is a Paper Pot Maker?

A paper pot maker is normally a two-part hand tool:

  1. a cylindrical mould around which paper is wrapped; and
  2. a base or press that creases and compresses the folded paper into a flat pot bottom.

 

EDAR's Paper Pot Maker page identifies the product as a wooden paper pot maker, item 200151, supplied in a colour box. The page describes using newspaper or paper scraps to form seed-starting pots. 

 

A formed newspaper pot is different from a moulded paper-pulp pot. The first is made by folding sheet paper around a tool; the second is manufactured from formed fibre. EDAR lists both a paper pot maker and ready-made paper seed starter pots, but they serve different buying and user needs.

What Paper Should You Use for Seedling Pots?

Plain, flexible, non-glossy newspaper is the most common starting material because it wraps and creases easily. Gardeners' Supply recommends plain, non-laminated newspaper rather than shiny magazine paper. Extension guidance also treats newspaper as a practical recycled seed-starting material while warning that coatings can slow breakdown.

Plain newspaper compared with coated and thermal paper for seed pots

Paper type Suitability What to verify
Plain newsprint Usually the easiest option Flexible, uncoated and free from plastic film
Plain kraft or grocery-bag paper Can work if thin and flexible May need a different strip length or fewer layers
Ordinary uncoated scrap paper Test before using Stiffness, ink, bleach treatment and breakdown behaviour vary
Glossy magazine or coated advertising paper Avoid as the default Coatings resist water and may delay breakdown
Laminated, waxed or plastic-lined paper Not suitable for direct planting The barrier layer may not break down with the paper
Thermal receipts Avoid Thermal coatings are not an appropriate default material for seed pots
Paper carrying tape, staples or labels Use only if every added material is removed or verified Adhesive, metal and plastic components change the disposal and planting route

 

Do not claim that all newspaper ink is soy-based or automatically safe. Ink formulations differ by publisher and market. For edible crops or commercial kits, identify the intended paper specification and obtain appropriate material information rather than relying on a general assumption.

How Much Paper and How Many Layers?

There is no universal strip size because paper pot makers differ in diameter and height. Use the tool itself to establish a cutting template.

A workable strip must:

  • wrap around the mould with enough overlap to hold the side wall together;
  • extend below the mould far enough for the bottom folds to meet or overlap;
  • finish near the intended pot height without leaving a large loose rim; and
  • remain easy to release after pressing.

 

Start with one or two wraps of thin paper and make a test pot. If the wall opens before filling, slightly increase overlap or add a layer. If the pot is bulky, difficult to remove or slow to wet, reduce the layers. Four-layer newspaper instructions exist for some homemade can-and-paper methods, but that is not a universal setting for every commercial mould.

 

The objective is a pot strong enough to fill and move while dry, yet not so thick that it creates a rigid barrier at transplanting.

How to Use a Paper Pot Maker Step by Step

1. Inspect and dry the tool

Make sure the mould and base are clean, dry and free from splinters or compacted paper. A damp wooden tool can make thin paper stick. If the product has a finish or care instruction, follow the supplier's guidance rather than soaking or sanitising it by default.

2. Cut a test strip

Wrap scrap paper around the mould once to estimate the required width and length. Leave enough paper below the mould to fold across the complete bottom. Mark this strip as the cutting template only after the finished test pot releases and stands correctly.

3. Wrap the mould

Place the mould near one end of the strip and roll the paper around it. Keep the edges aligned. The wrap should be snug enough to hold its shape but loose enough to slide off the mould. Do not pull the paper as tightly as gift wrap. An overtight wrap is one of the most common reasons a finished pot sticks to the tool.

4. Fold the bottom inward

Fold the paper overhang toward the centre in several overlapping sections. Cover the centre of the base rather than leaving an open hole. Keep the folds reasonably flat so the pot will stand upright.

5. Press the folded base

Place the wrapped mould into the shaping base. Press firmly and give a small twist if the tool is designed for that motion. The goal is to crease and compress the folds, not to tear the wettable paper or force the wooden parts together.

6. Release the pot

Lift the mould from the base and ease the pot off with a gentle twisting motion. If it resists, loosen the upper edge rather than pulling hard on the folded bottom.

7. Check the first result

Before batch production, confirm that the pot:

  • stands on a level surface;
  • has no large opening at the bottom;
  • keeps its side seam closed when lightly handled;
  • fits the intended support tray;
  • accepts the required amount of mix; and
  • releases without tearing.

Adjust strip length, width, overlap or number of layers one variable at a time.

8. Place pots in a waterproof tray

Arrange the empty pots closely together so neighbouring pots support one another. University of Maine Cooperative Extension specifically advises placing newspaper pots on a waterproof tray because their bottoms can weaken as seedlings grow.

9. Fill with growing medium

Add a suitable seed-starting mix in small amounts. Settle it gently; do not ram it into the paper wall. Leave enough headspace for sowing and watering. Follow the seed packet for sowing depth and crop-specific care.

10. Sow, label and water carefully

Sow the seed, label the pot and moisten the mix without blasting the paper wall. A fine spray can be useful for initial watering. Bottom watering may reduce surface disturbance, but remove residual standing water after the medium has absorbed enough unless the setup is specifically designed as a reservoir system. For a fuller explanation of temporary soak-and-drain watering, see EDAR's bottom watering seedlings guide.

Does a Paper Pot Need a Drainage Hole?

The pot must allow excess water to leave, but a separate punched hole is not always required. Newspaper walls and folded seams are porous, and the folded bottom often drains through its overlaps. Performance depends on paper type, layer count and how tightly the base is pressed.

 

Test the finished pot with the intended mix and watering method. If water remains trapped, change the paper construction or add a small drainage opening without weakening the base. Never assume that a decorative coated paper will drain like newsprint.

How to Keep Paper Pots from Falling Apart or Growing Mould

Paper softens when it remains wet. That is expected, but premature collapse usually indicates a mismatch between construction, watering and crop duration.

  • Keep formed pots together in a supportive waterproof tray.
  • Water the growing medium, not the outside wall.
  • Do not leave ordinary paper pots standing permanently in water.
  • Provide appropriate airflow after germination.
  • Avoid an excessively long indoor holding period in a small paper pot.
  • Lift the tray rather than carrying individual wet pots.
  • Remove dead plant material and keep the growing area clean.

 

Visible fungal growth on paper is a signal to review persistent moisture, airflow, sanitation and the propagation schedule. Do not promise that a particular paper or tool will be "mould-proof." If seedlings show stem collapse or root problems, isolate affected plants and diagnose the growing conditions rather than treating all surface growth as harmless.

Common Paper Pot Maker Problems

Symptom Likely causes First checks and corrections
Pot sticks to the mould Wrap too tight; too many layers; damp tool; rough surface Use a looser wrap, fewer layers and a dry clean mould
Side seam opens Too little overlap; stiff paper; pot handled alone when wet Increase overlap, test thinner paper and group pots in a tray
Bottom opens Insufficient overhang; folds do not meet; weak pressing Increase bottom allowance and overlap folds before pressing
Pot will not stand Bulky or uneven folds; base not pressed flat Use smaller folds and press on a level surface
Paper tears during pressing Paper too brittle; sharp edge; excessive force Change paper, inspect the tool and press firmly but gently
Pot collapses after watering Too few layers; prolonged saturation; unsupported handling Adjust construction, drain the tray and move pots as a group
Pot dries very quickly Porous wall, small volume, exposed air and warm conditions Check more frequently, group pots and adjust environment without waterlogging
Roots remain confined at transplanting Thick or coated paper; dry pot wall; short soil contact Remove/tear restrictive material or open the base before planting
Exposed rim dries the root ball Paper left above soil acts as a wick Tear off the rim or bury the complete paper edge

What Pot Size Should You Make?

The mould determines the finished diameter, while strip width and fold position affect height. Select the system according to crop, expected indoor holding period, watering routine and tray space-not simply the largest possible pot.

 

Small pots use less medium and fit more units per tray, but they have less water reserve and root volume. Larger pots can support a longer holding period but require more mix, more shelf space and more consistent handling.

 

EDAR's Seed Tray Cell Size Guide explains the same decision principle for propagation trays: match container volume to crop growth and the planned transplant date. Do not publish a crop-to-pot-size chart for a paper pot maker until the exact finished dimensions are confirmed.

Can You Plant a Newspaper Pot Directly in the Ground?

Often, yes-but inspect the pot rather than treating direct planting as automatic.

Before planting:

  • harden off the seedling as required for the crop and local conditions;
  • remove any tape, staple, plastic label or non-paper fastening;
  • check whether roots are reaching or penetrating the wall;
  • tear open the base if it remains thick or restrictive;
  • remove or bury every paper edge so none remains above the soil; and
  • water the root zone after planting.

 

Iowa State University Extension warns that an exposed biodegradable-pot rim can wick moisture away from the root ball. UC Cooperative Extension similarly advises that no newspaper should project above the soil and suggests opening folded bottoms to improve the route for roots.

 

If the paper is coated, unusually thick, still rigid or slow to wet, remove it carefully and transplant the intact root ball instead. "Plantable" does not guarantee the same breakdown speed in every soil, temperature or moisture condition.

Paper Pot Maker vs Ready-Made Paper Pots

Decision factor Paper pot maker Ready-made paper pots
User activity Requires cutting, wrapping and pressing Ready to fill
Pot consistency Depends on paper and technique Determined by manufactured specification
Retail experience Craft, education and reuse story Convenience and repeatable sizing
Material control End user selects the paper Buyer can specify and test the manufactured material
Best evaluation Tool finish, ergonomics, release and instructions Dimensions, wet strength, drainage and breakdown behaviour

For the wider material and handling comparison, use EDAR's Biodegradable Seed Starter Pots vs Plastic Seed Trays. Keep that comparison separate from this tool-use guide.

B2B Buyer Checklist for Paper Pot Makers

Retailers, importers and private-label buyers should assess the complete user experience, not only the appearance of the wooden parts.

Product specification

  • Confirm mould diameter, usable paper height and finished-pot dimensions.
  • Identify wood species, moisture content, surface finish and any adhesive used.
  • Check dimensional tolerance between mould and pressing base.
  • Inspect edges, grain, splinters, cracks and surface roughness.
  • Confirm item count and included components.
  • Verify all environmental, food-contact, coating, certification and sourcing claims before packaging.

Functional sample test

  • Provide one defined paper type and cutting template.
  • Have several first-time users form pots without verbal coaching.
  • Record release failures, torn bases, open seams and unstable pots.
  • Fill samples with the intended medium and place them in the target tray.
  • Repeat watering over the planned propagation period.
  • Check wet handling, base integrity and root exit at transplanting.
  • Test more than one paper thickness before stating compatibility.

Ergonomics and durability

  • Check grip comfort for adults and the intended supervised education market.
  • Test repeated pressing and twisting for loosening, cracking or surface wear.
  • Confirm that the base stays stable on a flat worktop.
  • Review cleaning and storage instructions for an unfinished or coated wooden tool.
  • Ensure instructions do not tell users to soak wood unless the finish is designed for it.

Packaging and instructions

  • Include a full-size paper cutting template or clearly dimensioned guide.
  • Show wrap direction, overlap, bottom allowance, fold sequence and release.
  • State the recommended paper characteristics rather than "any paper."
  • Explain waterproof tray support and careful watering.
  • Include direct-planting checks: remove fasteners, open restrictive bottoms and bury the rim.
  • Avoid universal claims such as guaranteed zero transplant shock, instant decomposition or suitability for every seedling.

Commercial range planning

  • Compare single-size and multi-size sets according to target retail price and crop use.
  • Confirm whether paper sheets, seeds, medium, labels or a tray are included; never imply components not in the approved bill of materials.
  • Test colour-box protection against humidity and impact during transit.
  • Specify language, barcode, warnings, origin marking and market-specific packaging requirements.
  • Coordinate the tool with EDAR's ECO-Friendly range without treating every item in that category as the same material or disposal route.

FAQ

Q: What paper is best for a paper pot maker?

A: Plain, flexible, non-glossy newsprint is the easiest default. Avoid laminated, waxed, glossy and thermal paper. For commercial instructions, specify the intended paper characteristics and test the exact thickness with the tool.

Q: How many layers of newspaper should I use?

A: Start with one or two wraps of thin paper, then test. Add overlap or a layer if the wall opens; reduce layers if the pot is bulky, sticks to the mould or remains restrictive at transplanting.

Q: Do paper pots need drainage holes?

A: They need drainage, but folded newsprint may drain through porous walls and base seams. Test the finished construction. Add an opening only if necessary and without weakening the base.

Q: Why does my paper pot stick to the maker?

A: The paper may be wrapped too tightly, too many layers may be used, or the tool may be damp or rough. Loosen the wrap, reduce layers and release with a gentle twist.

Q: Why does the bottom of my paper pot unfold?

A: The paper probably has too little overhang, the folds do not overlap, or the base was not pressed evenly. Increase the bottom allowance and make a test pot before cutting a batch.

Q: How do I water seedlings in newspaper pots?

A: Place the pots together in a waterproof support tray and moisten the growing medium gently. Check moisture frequently because porous walls can dry faster. If bottom watering, drain unused water after uptake rather than leaving ordinary pots permanently submerged.

Q: Is mould on newspaper pots normal?

A: Paper can support visible fungal growth when it stays damp. Review watering, airflow, sanitation and holding time. Do not assume that mould is harmless if seedlings are declining or stems are collapsing.

Q: Can I plant the entire paper pot?

A: You often can if the paper is plain, uncoated and already softening. Remove fasteners, open a restrictive base, and bury or tear off the rim. If the wall remains rigid, remove it carefully before transplanting.

Q: How long do paper seedling pots last?

A: There is no universal duration. Paper type, layers, watering, temperature, airflow and handling all affect wet strength. Test the complete setup for the intended propagation period rather than promising a fixed number of weeks.

Q: Is a paper pot maker suitable for children?

A: It can support supervised gardening activities, but suitability depends on the product's finish, size, required force, packaging and age guidance. Adults should inspect for splinters and supervise cutting, sowing and handling.

Conclusion

A paper pot maker works best when the tool, paper and growing method are treated as one system. Use plain non-glossy paper, create a complete folded base, keep the wrap loose enough to release, and test one pot before preparing a batch. Once filled, support the pots in a waterproof tray and control moisture carefully.

 

At transplanting, remove non-paper fasteners, inspect the base and bury the paper rim completely. For B2B sourcing, verify dimensions, finish, compatibility, wet performance and instructions on real samples. The strongest retail proposition is not an unqualified "zero-waste" promise; it is a clear, repeatable user experience with accurate material and planting guidance.

 

Send Inquiry

You Might Also Like